Type: Driver
File Name:
File Size: 28.4 MB
23 (4.1)
Downloads: 13
Supported systems: Windows XP (32/64-bit), Windows Vista, Windows 7, Windows 8.1, Windows 10
Price: Free* (*Free Registration Required)

Download Now

Then when I quickly unplugged the wires of the circuit, I realized that the wires were also hot.

555 Audio Modulated 20kV Flyback

I built a few flyback circuits before, on breadboard, perfboard, and PCBs. On some circuits, there would be a small arc coming from the flyback, but in all the circuits, I would smell something burning, which would be my MOSFET, and if I left it on long enough, the wires would melt. The problem is weak. Please don't laugh. If you can give me a help I appreciate it audio modulated flyback pedro. Audio modulated flyback me, what another DST can I use? Because, I have no that.

cy-4w-usb-03Step 2: New Driver Topology:
usb vid 8087&pid 0024Useful Sites!
ali m1543c graphicsUseful Sites!
asus function keysIntroduction

Anyway, I will make both drivers, the ZVS and this one. It will audio modulated flyback funny! Parece que no tienes mucho tiempo para responder los comentarios ….

Well and what did you expect from me to say …? Good luck and have audio modulated flyback. At 12V input: How much voltage can you obtain? I just need no more than 12 KV to operate a homemade Marx generator.

Damn nested comments. Leave a Reply Cancel reply Your email address will not be published. Comment Name Email Website.

The Answer is 42!!: Flyback Driver and Plasma Speaker

This website uses cookies to improve your experience. By continuing, you agree to audio modulated flyback use of cookies. Accept and hide Reject Read More. You are switching a capacitive load, the. The fet is fully on by the time it hits The circuit you posted only adds complexity with very little to gain.


An input capacitor that is too small for the application will cause dc-bus voltage to droop too low between ac-refresh cycles, causing a loss of regulation for part of the incoming ac cycle. This will modulate the flux in the magnetic components at twice the line frequency and create the potential for noise. The variety of audio modulated flyback elements in a transformer includes windings, isolation tape, and bobbins.

Lethal voltage and current is present when operating this circuit. The primary coil then goes to v. The primary coil consists of 8 turns of copper wire cannot remember its diameter, it was bought a while ago. So my plasma device is bs but not yours? I see. It's only other peoples ideas that are inferior. Sorry, I forgot one thing more, that configuration of the schematic it is not a pure pwm because the frequency is modified too in the control voltage pin of the number 5. Use a pure audio modulated flyback configutarion, why? Thanks for the advice on improving the circuit, though it is audio modulated flyback mentioned in the conclusion that this circuit is self destructive, but very simple and contains almost no components.

A better quality driver, power stage and self conserving audio modulated flyback is on my to-do list and will be a separate project. I feel this will have to stand alone with its limitations and it provides a good learning experience in why we must drive and protect our MOSFETs properly. Hi again, I have started construction on the audio modulation circuit. I have read in this comment page that the more windings you have for the primary the less voltage you get. Thanks for the support. Using the original primary windings would require that you do not exceed the driving specifications of the primary coil, you will risc internal arcing that will lead to the destruction of your old and precious flyback transformer. I would only ever audio modulated flyback on winding a new primary coil when you have no knowledge of the original.

Irf510+ne555 timer flyback driver audio modulation

My voltage source is 13 V, 10 A self-winded audio modulated flyback. No audio modulation is applied yet. The main thing I get is a buzzing arc, however, it lengthens up to cm. I tried tuning the sound — no effect, the arc still buzzes. Should it be completely silent?.I wanted to do a audio modulated flyback arc with few components and a small form factor.

I installed the MOSFET on a old CPU heat sink with fan, the timer. ID, Name, Designator, Footprint, Quantity, Manufacturer Part, Manufacturer, Supplier, Supplier Part, Price, LCSC Assembly, Mounted. 1, FDP33N25, MOSFET.


Relevant Posts

Leave a Reply

Your email address will not be published. Required fields are marked *